Kenmore Ice Maker Parts Diagram

In Diagram, Other, Wiring 40 views

The most effective method to supplant an ice producer in a next to each other cooler

This DIY fix guide tells well ordered the best way to supplant a manufacturing plant introduced ice creator in a next to each other cooler. The ice producer get together has electronic parts that can breakdown and keep water from filling the ice creator shape or from dropping the ice from the shape after it structures. Supplant the ice producer get together utilizing the maker endorsed new part in the event that it quits working.

These fix guidelines work for Kenmore, Whirlpool and KitchenAid one next to the other iceboxes with in-entryway ice frameworks. kenmore ice maker parts diagram

Close off power and water to the fridge

Unplug the fridge or shut off the electrical switch for the icebox.

Close the water supply cut-off valve for the water line joined to the back of the icebox. The valve is frequently on the divider behind the cooler yet could be under the kitchen sink or in the storm cellar underneath the fridge.

Evacuate the ice creator’s title page

Use tape to close the flipper spread on the left divider before the ice creator.

Open the plastic spread before the cooler ice creator. Slide the spread to one side and push up on the correct side of the spread to discharge the plastic stick from the section. Utilize a space screwdriver to pry the stick from the section, if essential.

Draw off the spread and put it in a safe spot.

Tape the flipper shut.

Evacuate the wire outfit spread

Utilizing a 1/4-inch nut driver, evacuate the screw that is under the ice producer module, in the back right corner. Draw off the spread that the screw held set up. Put the screw and plastic spread in a safe spot.

Evacuate the ice producer

Push in on the tab to one side of the ice producer to discharge the ice creator and slide the ice creator forward, off its rails.

Utilize a space screwdriver to discharge the locking tab on the wire saddle fitting and haul the wire tackle out of the attachment.

Expel the ice creator from the cooler compartment. Close the cooler entryway. kenmore ice maker parts diagram

Expel the mounting plate

Spot the ice producer module topsy turvy on a level surface. Utilizing a 1/4-inch nut driver, expel the screws that safe the base mounting plate to the base of the ice producer module.

Discharge the locking tabs on both side of the wire outfit plug that protected it to the plastic base mounting plate. Haul the wire tackle attachment out of the base mounting plate to discharge the ice producer module.

Put the old ice creator in a safe spot for transfer.

Append the mounting plate to the new ice producer get together

Position the new ice creator in the base plastic mounting plate and push the plastic wire outfit plug into the side of the mounting plate until the plastic locking tabs fit properly.

Line up the screw gaps on the base of the plastic mounting plate. Supplement the screws and fix them simply past hand tight.

Fitting in the wire bridle

In the cooler, hold the ice creator close to the mounting rails and attachment in the wire outfit into the association plug until the locking tab fits properly.

Slide the ice producer get together onto the mounting rails

Inside the cooler compartment, line up the new ice producer with the mounting rails and push it onto the rails until you can position the fill tube in the fill cup. Put the fill tube into the cup.

Slide the ice producer module into position until the locking tab fits properly.

Supplant the wire bridle spread

Position the plastic wire bridle spread and screw it into spot. Fix the screws until they quit turning and after that give them a sensibly firm contort to verify them. Don’t overtighten.

Reattach the title page

Position the front plastic spread before the mounting clasp and addition the left side stick into the mounting cut. Work the correct side stick over the highest point of the mounting clasp and adjust it properly.

Expel the tape that holds the flipper spread.

Reestablish water and power

Open the water supply shut-off valve to reestablish the water supply to the icebox.

Fitting in the cooler or turn on the house electrical switch to reestablish control.

The most effective method to Reset a Kenmore Ice Maker

When supplanting a Kenmore ice creator in the icebox, it may end up important to reset the gadget to work appropriately with your cooler. Resetting the ice creator will make an impression on the PC board in the unit, enabling it to be perceived by the Kenmore icebox. This is a genuinely basic procedure you can achieve in merely minutes without reaching a repairman to play out the activity or spending any cash on fixes.

Stage 1

Find the spread plate on the facade of the Kenmore ice producer, and force the plate off the front of the ice creator by hand.

Stage 2

Find the on/off switch for the ice producer on the facade of the PC board, and turn the change to the “Off” position.

Stage 3

Unplug the icebox from the electrical outlet for five minutes.

Stage 4

Fitting the fridge once again into the electrical outlet, and turn the PC switch on the ice producer to the “On” position.

Stage 5

Put the spread plate back on the facade of the ice creator, snapping it back set up and close the entryway of the cooler, giving it a chance to sit for four minutes.

Stage 6

Enable time for the ice creator to experience a cycle and check that the unit is working appropriately.kenmore ice maker parts diagram

author
Author: 
    How to Operate Kubota Tractor Parts Diagram
    How to Operate Kubota Tractor Parts Diagram
    Step by step instructions to Operate a
    Lewis Dot Diagram Worksheet Answers
    Lewis Dot Diagram Worksheet Answers
    Instructions to Draw a Lewis Structure A
    House Drainage System Diagram
    House Drainage System Diagram
    Foul Drainage. At the point when the
    How To Make a Venn Diagram
    How To Make a Venn Diagram
    What is a Venn Diagram? A Venn
    When Do Baby Teeth Fall Out Diagram
    When Do Baby Teeth Fall Out Diagram
    Dental Health and Your Child’s Teeth The
    Craftsman 42 Inch Mower Deck Belt Diagram
    Craftsman 42 Inch Mower Deck Belt Diagram
    Can a Craftsman Lawn Tractor Belt be
    How to Install And Bridge a 4 Channel amp Wiring Diagram
    How to Install And Bridge a 4 Channel amp Wiring Diagram
    Step by step instructions to Install a
    Mobile Home Plumbing Diagram
    Mobile Home Plumbing Diagram
    Manufactured home Plumbing What is the contrast

    Leave a reply "Kenmore Ice Maker Parts Diagram"

    Must read×

    Top