Kenmore he2 Dryer Parts Diagram

In Diagram, Other, Wiring 27 views

The most effective method to Open a Kenmore Dryer Panel

Regardless of what you have to supplant inside your Kenmore dryer—the belt, the engine, the idler, the drum underpins or nearly whatever else—you will initially need to evacuate the front dryer board. Luckily Kenmore makes this piece of your dryer support simple, notwithstanding for low maintenance do-it-yourselfers with restricted understanding. Try not to be scared by your dryer—from various perspectives it is the most effortless machine to take a shot at. kenmore he2 dryer parts diagram

Stage 1

Unplug your dryer from the electrical outlet.

Stage 2

Open the build up snare spread if there is one and expel the build up snare. Find the two screws that are simply under the build up channel and evacuate them. Put them aside in a protected spot.

Stage 3

Handle the highest point of the dryer immovably with one hand on either side and draw toward you pointedly and afterward lift up marginally. This will discharge the highest point of the dryer from the two springs that hold the front board to the machine.

Stage 4

Take a gander at the back of the machine. Close to the top will be two screws. Evacuate them and protect them. On certain models the screws are Phillips; on different models you will require a level screwdriver, on still different models you will require a little sickle wrench to evacuate these two screws.

Stage 5

Delicately lift up on the highest point of the machine. On certain models the front will lift up, and on different models the back lifts up toward you. Take a gander at the wires that are joined to the top and note their request. Handle the connectors and haul the wires straight out so you can lift the top as far as possible up.

Stage 6

Lift up marginally on the facade of the machine to discharge the spring cuts that hold the base edge of the front board and after that draw the front board away from the machine and set it to the other side. You currently have full access to the inside of your Kenmore dryer. kenmore he2 dryer parts diagram

The most effective method to Take the Front Panel Off of a HE2 Kenmore Dryer

Stage 1

Unplug the HE2 dryer power string.

Stage 2

Expel the screws along the back of the top board. Lift the back of the top board. Destroy back to separate it from the bureau. Put the top board in a safe spot.

Stage 3

Unplug the electrical connector driving from the control reassure to the bureau. Press the two locking tabs on the back of the comfort to open them.

Stage 4

Force the reassure down and away from the dryer to disengage it. Put the support in a safe spot.

Stage 5

Unplug the entryway switch electrical outfit prompting the front board.

Stage 6

Open the dryer entryway. Expel the build up channel. Expel the two screws alongside the channel compartment.

Stage 7

Expel the screws at the base of the toe board. Lift the toe board down and away from the dryer to expel it. Put the toe board in a safe spot.

Stage 8

Expel the two screws along the highest point of the front board. Lift the front board off of the Kenmore HE2 dryer bureau.kenmore he2 dryer parts diagram

author
Author: 
    Toyota Tacoma Body Parts Diagram
    Toyota Tacoma Body Parts Diagram
    Step by step instructions to: Cleaning Throttle
    How to Repair And Fix Pella Storm Door Parts Diagram
    How to Repair And Fix Pella Storm Door Parts Diagram
    Instructions to Repair a Pella Storm Door
    Cub Cadet Parts Diagram lt1050
    Cub Cadet Parts Diagram lt1050
    The most effective method to Repair Small
    How to Wire 2 lamp t8 Ballast Wiring Diagram
    How to Wire 2 lamp t8 Ballast Wiring Diagram
    Instructions to Wire a T8 Ballast A
    Chevy s10 Exhaust System Diagram
    Chevy s10 Exhaust System Diagram
    Step by step instructions to Install an

    Leave a reply "Kenmore he2 Dryer Parts Diagram"

    Must read×

    Top