How To Replace Rear Drum Brake Diagram Chevy 96-00 Tahoe

In Diagram, Other, Wiring 104 views

stage 1: Removing The Wheel and Tire

  • Loosen the fasteners
  • Raise and Secure the vehicle
  • Remove the fasteners
  • Remove the haggle

stage 2: Applying Penetrating Oil

  • Douse each wheel stud with entering oil
  • Let sit
  • Rotate the brake 180 degrees
  • Douse each wheel stud with entering oil once more
  • Let sit .rear drum brake diagram chevy

stage 3: Removing the Brake Drum

  • Make sure to wear security glasses
  • Use the sledge to relax up the brake drum
  • Remove the brake drum

stage 4: Removing the Brake Hardware

  • Remove the springs utilizing the bad habit hold or the brake spring instrument
  • Remove the spring for the agent switch
  • Remove the pins by driving a turning them with the bad habit hold
  • Remove theseperator bar to pull the shoes free
  • Put equipment aside if reusing it

stage 5: Removing the Brake Shoes

  • Use the little screwdriver to drive the clasp off the joining pin
  • Remove the brake shoes

stage 6: Seperating the Emergency Brake Lever and the Adjuster

  • Push the shoes together by hand
  • Pull off the agent and spring
  • Pry the crisis brake switch off with the screwdriver

stage 7: Cleaning the Backing Plate

  • Clean the support plate with a wire brush

stage 8: Inspecting the Adjuster

  • Make sure the agent turns unreservedly
  • Make sure all pieces of the agent turn autonomously
  • If utilizing another agent, grease up the strings

stage 9: Connecting the Brake Shoes

  • Identify the back shoe by examining the covering
  • Attach the agent and spring
  • Connect the front shoe to the agent and spring .rear drum brake diagram chevy

stage 10: Installing the Brake Shoes

  • Apply oil to spaces on rear of shoes
  • Apply oil to the sponsorship plate
  • Put the shoes set up
  • Thread sticks through from the back, beginning with the front shoe
  • Attatch the springs with the bad habit grasps
  • Put the crisis brake switch behind the back shoe
  • Attach the spring washer and locking cut
  • Replace the separator bar and switch
  • Attach the equipment for the back shoe
  • Reattach the springs utilizing the bad habit grasps

stage 11: Installing the Drum

  • Slide the drum into spot
  • Test the fit
  • Run out the agent
  • Try the drum once more
  • Continue to modify until the drum hauls to some degree

stage 12: Adjusting the Brakes

  • Remove the elastic fitting behind the sponsorship plate
  • Tighten the brakes with a brake spoon
  • Test the fit
  • Back off the alteration if fundamental
  • Apply infiltrating oil
  • Replace the elastic fitting

stage 13: Replacing the Wheel

  • Slide the wheel back on
  • Replace the fasteners
  • Start Tightening the fasteners
  • Let the vehicle to the cold earth
  • Torque the fasteners to 110 foot-pounds

stage 14: Testing the brakes

author
Author: 
    How to Operate Kubota Tractor Parts Diagram
    How to Operate Kubota Tractor Parts Diagram
    Step by step instructions to Operate a
    Lewis Dot Diagram Worksheet Answers
    Lewis Dot Diagram Worksheet Answers
    Instructions to Draw a Lewis Structure A
    House Drainage System Diagram
    House Drainage System Diagram
    Foul Drainage. At the point when the
    How To Make a Venn Diagram
    How To Make a Venn Diagram
    What is a Venn Diagram? A Venn
    When Do Baby Teeth Fall Out Diagram
    When Do Baby Teeth Fall Out Diagram
    Dental Health and Your Child’s Teeth The
    Craftsman 42 Inch Mower Deck Belt Diagram
    Craftsman 42 Inch Mower Deck Belt Diagram
    Can a Craftsman Lawn Tractor Belt be
    How to Install And Bridge a 4 Channel amp Wiring Diagram
    How to Install And Bridge a 4 Channel amp Wiring Diagram
    Step by step instructions to Install a
    Mobile Home Plumbing Diagram
    Mobile Home Plumbing Diagram
    Manufactured home Plumbing What is the contrast

    Leave a reply "How To Replace Rear Drum Brake Diagram Chevy 96-00 Tahoe"

    Must read×

    Top