How To Repair a Hayward Pool Vac Parts Diagram Pool Vac Ultra Pool Cleaner

Step by step instructions to Repair a Hayward Navigator or Pool Vac Ultra Pool Cleaner

On the off chance that your programmed pool cleaner isn’t working effectively, it might be a great opportunity to supplant the parts that are intended to wear. On the off chance that you see huge wear on your cleaners shoes, wings or folds, supplant these parts to improve execution, and to anticipate harm to the more exorbitant segments. hayward pool vac parts diagram

Stage 1

Turn your Navigator/Pool Vac Ultra pool cleaner over and take a gander at the cleaner’s shoes. The image at left demonstrates a case of seriously worn shoes. At the point when the shoe is pushed facing the finish of the unit, the shoe ought to reach out over the outside of the case or the case will begin to rub against the pool floor. This shoe ought to have been supplanted before the outside of the shoe had worn beneath the outside of the unit.

Stage 2

This image demonstrates a Navigator/Pool Vac Ultra with new shoes. Note how far the shoe stretches out over the unit surface.

Stage 3

Next examine the Navigator/Pool Vac Ultra’s wings for wear and breaks. There is a wear line on every one of the wings. When you can never again observe this line, supplant the wings. The image at left demonstrates a case of a gravely worn and broken wing. At 1, the wing has worn through by the peg that holds it in. At 2, the opening in the wing has worn to the point of breaking. Not appeared – the tip of the wing has worn past its substitution line.

Stage 4

Presently examine the Navigator/Pool Vac Ultra’s folds (back and front) for wear and splits. The image at left demonstrates a case of a well used back fold that should be supplanted.

Stage 5

When supplanting Navigator/Pool Vac Ultra parts, consider acquiring a pool cleaner adjust pack. In the event that one lot of parts requires substitution, it’s most likely a decent time to supplant these parts. This unit incorporates a lot of 4 shoes, a lot of 2 wings, a lot of 2 folds (front and back) and a screwdriver and brush to introduce the parts. When you buy this pack, check to ensure you buy the unit with the right shoes. Shoes for cement or gunite pools are not the same as shoes for fiberglass of vinyl pools.

Stage 6

For simplicity in supplanting these parts, detach the pool cleaner from its hose. Destroy the hose straight off to abstain from breaking the inner apparatuses.

Stage 7

To supplant the shoes, first turn the pilot on its back. At that point embed a screwdriver between the shoe and the case to pry the shoe off.

Stage 8

Next dunk another shoe in the water for grease and press it onto the openings in the unit. Note, the two fittings on the shoe fit into two diverse size gaps, one greater that the other. This guarantees the shoes are appropriately connected. Press until you feel it fit properly. Rehash for the other three shoes.

Stage 9

To remore the wings, first evacuate the fitting over the wing from the unit.

Stage 10

Evacuate the old wing by bowing it somewhat and lifting it off their snares on the case. Note: If any of the wing snares are broken, you should supplant the case. See other “How To Guides”.

Stage 11

Spot another wing onto the unit snares. There are markings for “R” or “L” on the wings and each case. Ensure these coordinate. hayward pool vac parts diagram

Stage 12

Supplant the case attachment and tap then into the right spot with the screwdriver handle. Rehash this procedure for the other wing.

Stage 13

To supplant the back and front folds, embed the screwdriver between the fold and the lower body, close to the rotate purpose of the folds. Delicately pry the fold turn call attention to or the opening in the body and slide the fold out. Rehash to evacuate the other fold.

Stage 14

Note that the new folds are stamped “Back” and “Front”. Make a point to introduce the best possible fold in the front and genuine of the unit. The back of the unit has the screen in it. When introducing the front fold, make sure that the all-inclusive leg of the spring is embedded into the score on the facade of the lower body. Push the fold set up with the goal that the turn nibs connect with the rotate openings in the body. Crease the fold in towards the base of the more clean. There will be some opposition until the fold fit properly. Watch that the spring is set up and that the spring activity works unreservedly.

Stage 15

When introducing the back fold, ensure that the spring leg is set on the cam on the back fold agent. As the back fold is pushed into spot, it will snap into its ordinary working position. Watch that the two folds move unreservedly and that the two of them spring up.

Stage 16

Turn the Navigator/Pool Vac Ultra right side up and take a gander at the lower left half of the unit. Search for the blue back fold agent, a round handle about the size of a pencil eraser with a bolt opening. You will see the Roman numerals I, II and II around the agent. With a screwdriver turn the space so its bolt indicates the II. This is the ordinary activity level for the more clean. I setting eases back the Navigator/Pool Vac Ultra down if it’s climbing the dividers or staying in corners; III setting speeds the Navigator/Pool Vac Ultra up on the off chance that it can’t climb the slants.

Stage 17

Utilize the since quite a while ago dealt with brush from the pack to clean the screen at the back of the Navigator/Pool Vac Ultra. This screen enables water to stream into the Navigator/Pool Vac Ultra’s directing system. In the event that the water stream is discouraged, the Navigator/Pool Vac Ultra directing can’t work appropriately.hayward pool vac parts diagram

author
Author: 
    Fire Fighting Sprinkler System Diagram
    Fire Fighting Sprinkler System Diagram
    The most effective method to INSTALL A
    How to Butcher a Pig Diagram
    How to Butcher a Pig Diagram
    In the event that you’ve at any
    Ford Ranger Door Parts Diagram
    Ford Ranger Door Parts Diagram
    The most effective method to Get in
    How to Change the Oil Arctic Cat ATV Parts Diagram
    How to Change the Oil Arctic Cat ATV Parts Diagram
    The most effective method to Change the
    How to Install a Kitchen Sink Drain Assembly Diagram
    How to Install a Kitchen Sink Drain Assembly Diagram
    Step by step instructions to Install a
    How To Repair Little Giant Pump Parts Diagram
    How To Repair Little Giant Pump Parts Diagram
    Step by step instructions to Repair a
    Network Diagram Software Open Source
    Network Diagram Software Open Source
    Top 10 Network Diagram, Topology and Mapping
    Snapper Riding Mower Parts Diagram
    Snapper Riding Mower Parts Diagram
    Step by step instructions to Troubleshoot a

    Leave a reply "How To Repair a Hayward Pool Vac Parts Diagram Pool Vac Ultra Pool Cleaner"

    Must read×

    Top