Hayward Super ii Pump Parts Diagram

In Diagram, Other, Wiring 12 views

Step by step instructions to Rebuild the Hayward Super Pump

Devices required:

  • green-check 7/16″ wrench
  • green-check 9/16″ wrench
  • green-check Rubber gloves
  • green-check Adjustable channel-lock pincers
  • green-check Large level head screwdriver.hayward super ii pump parts diagram

Step by step instructions to Replace Seals in a Hayward Super II Pool Pump

The dissemination siphon in a pool hauls water out of the pool through the skimmers under negative weight, at that point siphons it through the channel and once more into the pool through the arrival lines under positive weight. Hayward’s Super II siphon is a self-preparing, high-yield unit intended for in-ground pools. The siphon impeller load is darted to the siphon engine and an elastic spring seal around the impeller center point mates with an artistic seal in the seal plate to forestall water spillage from the impeller into the engine. At the point when this seal wears and falls apart, spillage might be watched exuding from the base of the siphon. The producer’s seal fix pack comprises of an elastic spring seal, an artistic seal and a lodging seal.

Disengage electrical capacity to the siphon at the principle switch or electrical switch. Confirm that power is detached, utilizing an inductive multimeter.

Close the valve in the admission line before the siphon and turn the multiport valve at the channel to the “Shut” setting.

Evacuate the six, 3/8-inch by 2-inch jolts tying down the engine rib to the siphon lodging, utilizing an attachment and attachment wrench.

Separate the engine from the siphon lodging by pulling it straight outward from the lodging.

Force the diffuser that covers the impeller on the finish of the siphon off of the impeller.

Evacuate the two, 1/4-inch hex screws tying down the engine spread to the back of the engine and expel the spread.

Slide a 7/16-inch open-end wrench between the enormous capacitor and the radial switch system so the wrench fits on the level spots on the engine drive shaft that projects from the back of the engine.

Hold the wrench with one hand to keep the engine drive shaft from turning. With the other hand, unscrew the impeller unit off the front finish of the drive shaft by turning it counterclockwise and uncovering the seal get together.

Haul the close plate behind the impeller the engine get together after the impeller is evacuated.

Analyze the two-section seal get together. The elastic spring seal get together is on the impeller center point within face of the impeller. The fired portion of the seal gathering is introduced in a score in the seal plate.

Delicately pry the clay seal out of the furrow in the seal plate, utilizing a flathead screwdriver. Draw the elastic spring seal off the impeller center point within face of the impeller. Expel the huge lodging gasket from the seal plate. hayward super ii pump parts diagram

Grease up the notch in the seal plate and the impeller center point on the impeller, utilizing fluid dish cleanser.

Press the substitution fired seal into the score in the seal plate with the cleaned side of the seal confronting outward. Wipe the uncovered surface of the artistic seal with a perfect fabric.

Slide the substitution spring seal onto the impeller center point with the cleaned surface of the seal confronting outward. Wipe the cleaned surface of the spring seal with a perfect material.

Slide the substitution lodging gasket onto the seal plate.

Introduce the seal plate onto the engine mounting plate. The tabs on the seal plate ought to line up with the notches in the engine mounting plate.

Slide a 7/16-inch open-end wrench between the huge capacitor and the outward switch instrument so the wrench fits on the level spots on the engine drive shaft that juts from the back of the engine.

Hold the wrench with one hand to keep the engine drive shaft from turning. With the other hand, screw the impeller unit onto the front finish of the drive shaft by turning it clockwise. Fix the impeller by hand safely.

Introduce the impeller ring onto the front of the impeller with the rib confronting outward toward the diffuser. Push the diffuser over the impeller.

Supplant the engine end spread and fix the two, 1/4-inch jolts tying down the spread to the back of the engine.

Slide the engine get together into the siphon lodging. Guarantee the lodging seal isn’t harmed or exasperates as the engine gathering contacts the lodging.

Secure the engine get together to the siphon lodging, utilizing the six, 3/8-inch by 2-inch jolts. Fix the jolts, utilizing an attachment and attachment wrench.

Open the admission valve and pivot the multiport valve to the “Channel” setting. Reestablish capacity to the siphon at the electrical switch.hayward super ii pump parts diagram

author
Author: 
    How To Clean Troy Bilt Pressure Washer Carburetor Diagram
    How To Clean Troy Bilt Pressure Washer Carburetor Diagram
    The most effective method to Clean Carburetor
    How to Start And Repair Toro Lawn Mower Parts Diagram
    How to Start And Repair Toro Lawn Mower Parts Diagram
    Instructions to Start Toro Lawn Mowers Toro
    PT Cruiser Rear Suspension Diagram
    PT Cruiser Rear Suspension Diagram
    Suspension tips and deceives The rotate point
    How To Clean Diagram For Briggs And Stratton Carburetors
    How To Clean Diagram For Briggs And Stratton Carburetors
    The most effective method to Clean and
    How To Fix Lazy Boy Recliner Parts Diagram
    How To Fix Lazy Boy Recliner Parts Diagram
    Step by step instructions to Fix a
    How to Prime And Replace Sta Rite Pump Parts Diagram
    How to Prime And Replace Sta Rite Pump Parts Diagram
    Step by step instructions to Prime a

    Leave a reply "Hayward Super ii Pump Parts Diagram"

    Must read×

    Top